Pressure-Treated Wood and Arsenic: Deck and Playground Safety
If your deck or playset was built before 2005, it may be CCA pressure-treated wood, often with a greenish tint or old preservative tags, and it can shed arsenic as rain, UV, and wear bring residues to the surface. Kids face the biggest risk through hand-to-mouth contact; studies report about 40 µg of dislodged arsenic per 100 cm² after a month of weathering, and realistic play can add tens of micrograms per day. You’ll also want practical ways to reduce exposure and safer replacement options.
Is This CCA Pressure-Treated Wood (Pre-2005 Clues)?
How can you tell if your deck or playground uses older CCA pressure-treated wood? Start with the build date: CCA dominated residential decks and playsets from the early 1970s through 2003, with consumer production ending January 1, 2004. If the structure predates 2005 and still looks remarkably durable, you should assume residual CCA remains.
Next, inspect color. CCA often leaves a greenish tint from chemical impregnation; heavier treatment can look deeper green. Many post-2004 options (ACQ, CA, MCQ, MCA) don’t show that distinctive green cast, so a green hue plus older construction increases your odds.
Look for regulatory clues. Pre-phase-out CCA products required labeling; any remaining tags or stamps can confirm it. Tags on treated lumber also list the preservative type and its intended use category under AWPA standards. When you’re evaluating exposure risk, remember wipe samples from CCA surfaces averaged 105 µg arsenic/100 cm².
How Does Arsenic Leach From CCA-Treated Wood?
Even if CCA-treated boards look solid, rain and weathering pull arsenic out of the wood and move it into places you touch and track—surface residues, surrounding soil, and runoff water. Water penetrates the lumber, dissolves water‑soluble CCA components, and transports them back to the surface, where residues can dislodge. After just one month of weathering, studies report about 40 µg arsenic per 100 cm² dislodged on average (6–122 µg/100 cm²). Municipal park playscapes also show measurable residues, averaging 8.8 µg/100 cm² of dislodged arsenic. UV exposure and cycles of sun and moisture increase release of chromium, copper, and arsenic, and leachate from tested CCA wood can exceed the 5 mg/L federal toxicity limit. Arsenic leaves mainly as inorganic As(V) and As(III); As(III) can dominate early, then As(V) increases over time as conditions shift. Soil pH and type control where it ends up—clay/alkaline soils bind more than sand.
How Risky Is CCA Wood for Kids’ Hands and Skin?
Where does the real risk show up when kids climb and grip CCA-treated boards? It’s not mainly what soaks through skin—it’s what ends up in their mouths. Direct hand contact can dislodge arsenic residues, and frequent hand-to-mouth activity makes oral ingestion the dominant exposure pathway on decks and playgrounds. Realistic play patterns can produce doses in the tens of micrograms per day, which matters more for smaller bodies. A simple protective step is to seal the wood, since common coatings can cut arsenic dislodgement by more than 95%.
Skin contact still isn’t benign. Inorganic arsenic is virtually not absorbed through intact skin, so systemic dose from touch is low, and most assessments treat dermal exposure as secondary. But residues can irritate, causing redness or swelling, and long-term low-level contact has been linked to thickening or darkening. The bigger concern is downstream risk: arsenic is a known human carcinogen, and EPA modeling indicates most repeatedly exposed children exceed a 1-in-1,000,000 cancer risk threshold.
How Do You Reduce Arsenic on CCA Wood Surfaces?
In practice, reducing arsenic on CCA wood surfaces means cutting down the arsenic that can rub off onto hands and then get swallowed. Start with low-dust cleaning: rinse and wipe gently, and don’t hard-scrub. Avoid sanding or scraping weathered boards because you’ll create contaminated dust and raise exposure. If you’re handling freshly treated lumber, guarantee fixation: air-dry about 3 weeks above 16°C or kiln-dry to under 30% moisture; better fixation means less surface leaching.
Retention level is crucial for treatment quality and is expressed as the weight per unit volume.
Next, seal what people touch. Apply an oil- or water-based penetrating stain, or brush on a water-repellent preservative (typical life 1–3 years). For higher-contact areas, use encapsulation: an epoxy sealer base coat plus two flexible elastomeric acrylic coats; higher resin, thicker films retain arsenic longer. Two-coat applications statistically reduce dislodgeable arsenic for about 12 months. Recoat yearly as weathering accelerates leaching.
What Can You Use Instead of CCA-Treated Wood?
How can you cut arsenic exposure at the source? Replace CCA lumber when you build, repair, or resurface decks and play sets. Since CCA production for residential uses stopped by 2004 under an EPA voluntary phaseout, you can usually choose arsenic-free materials without sacrificing durability.
For wood that still needs preservative protection, pick water-based Copper Azole (a common CCA replacement) or consider low–acute-toxicity options like copper naphthenate or zinc naphthenate. For enclosed, dry applications, borate treatments (including Copper-8 and Niedox-10 with boric acid) offer lower-toxicity control of insects and decay.
If you’d rather avoid preservatives, use naturally durable heartwood species such as redwood or cedar, or pay more for durable hardwoods like mahogany; look for FSC-certified sourcing. The EPA does not recommend replacing or removing existing structures made from CCA-treated wood.
For the lowest contact transfer risk, choose composites (recycled plastic or wood-plastic blends) or non-wood materials like recycled steel, fiberglass, concrete, or painted metal.
Frequently Asked Questions
Can I Safely Burn Old Pressure-Treated Wood in a Fire Pit?
No—you can’t safely burn old pressure-treated wood in a fire pit. Heating it can release arsenic, chromium, and copper into smoke you’ll inhale, irritating eyes and lungs and raising cancer risk. The ash concentrates toxins; even small amounts can harm people and pets. Burning it’s illegal nationwide. You should bag and take it to an approved disposal site and burn only untreated, seasoned hardwood.
How Do I Dispose of Cca-Treated Lumber, Sawdust, or Demolition Debris?
You’ll dispose of CCA-treated lumber, sawdust, and demo debris by bagging it, separating it from clean wood, and taking it to a permitted C&D or municipal solid-waste landfill. One key data point: EPA exempts CCA-treated wood from hazardous-waste rules under 40 CFR 261.4(b)(9), so it typically goes as solid waste. Don’t burn, chip, or compost it—those raise inhalation and ash exposures. Check state/local rules and keep disposal records.
Is It Safe to Plant Vegetables Near a Cca-Treated Deck or Raised Bed?
No—you shouldn’t plant vegetables close to CCA-treated wood because arsenic can leach into nearby soil and enter crops, especially in acidic, sandy soils. Studies show up to a ten-fold arsenic increase in lettuce and tomatoes grown in CCA-bed soil, and higher uptake in roots like radishes and spinach. You’ll reduce exposure by keeping distance, adding a liner/barrier, replacing wood, and avoiding phosphate fertilizers.
What Are the Symptoms of Arsenic Exposure From Treated Wood Contact?
From brief contact, you might see redness and swelling—yet heavy ingestion can flip to nausea, vomiting, diarrhea, and stomach irritation. With repeated low-level exposure, you can develop darkened, thickened skin, lesions, and small corns/warts on palms and soles. You may notice garlic-like breath, abdominal pain, headaches, pins-and-needles, Mees lines, and—1–3 weeks later—sensorimotor neuropathy with slower nerve conduction.
Are There Test Kits to Measure Arsenic in My Soil or on Wood Surfaces?
Yes—you can use field test kits for both soil and wood. For wood, you’ll drill a 1/16-inch interior sample; the Arsenic Quick Mini-kit detects ~1 µg inorganic arsenic in 10–14 minutes via a yellow-brown strip. For soil, the Quick Arsenic Mini kit detects 0.3 ppb in ~12 minutes, below the 10 ppb EPA MCL. You can also screen fast with portable XRF.